Lathem 6000E Bedienungsanleitung Seite 1

Lathem Time CorporationENGLISH

7Once the AC line cord is plugged into the outlet, the unit can be used immediately as basic operation has been pre-set at the factory

8To prepare for setting:5. SETTINGPreparation for setting1 Unlock the unit. While holding down the panel open buttons at both sides of the u

DAY ADV.TIME D.S.T PROGRAM EXT.ALARMSETPAY ENDINGSELECTYEARRED/BLK.MONTHEX.ALMDAYCOL.HOUR MINUTE SECOND/CARDDATE/TIMESU 12Hr. TU SAFRTHWEMO1/601/1009

101 Remove the panel cover.Make sure that the PAY ENDING button stays lit up.2 Press or to cause the digits at the right to flash (

111 Remove the panel cover.Make sure that the PAY ENDING stays lit up.2 Press or to cause the digits at the right to flash "00

5 Press or to cause the digits at the left to flash "L-1".7 Check the settings on the display and press SET .6 Press

Setting the Date and the Time, 1/60 or 1/100 printing, the 12/24 HOUR formatThe DATE/TIME button stays lit up during its setting operation.1 Press S

4 Setting for 1/60 or 1/100 printingPress or to cause the digits at the upper left to flash.Press or to select the

Setting the Day Advance TimeThe day advance time refers to the time when printing shifts to the next line on a time card for the next day. This f

Setting the Daylight Saving Time (D.S.T.)Daylight saving time function 1 D.S.T. execution timeAt 2:00 a.m. on the first day of summer time,

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are de

s$AYLIGHTSAVINGTIMEISNOTPRESETATTHEFACTORYWITHTHEINDICATIONOFMONTHANDDAYs4HE$34BUTTONSTAYSLITUPDURINGITSS

DAY ADV.TIME D.S.T PROGRAM EXT.ALARMSETPAY ENDINGSELECTYEARRED/BLK.MONTHEX.ALMDAYCOL.HOUR MINUTE SECOND/CARDDATE/TIMESU 12Hr. TU SAFRTHWEMO1/601/1003

Setting the Time Table ProgramThe time table program function allows automatic selection of print color (black or red), an external time signal, and

Follow the steps to set time table programs.1 Press SELECT to cause the PROGRAM button light up.DAY ADV.TIME D.S.T PROGRAM EXT.ALARMSETPAY ENDINGSELEC

2 To set P-01 (shown in the table above)(1) Print colorWith "P-01" flashing, press once. The print color indication flashes

Press again. The minute indication flashes. Leave the digits as they are since the desired time is 05:00 in this case.(5)Day of the week

DAY ADV.TIME D.S.T PROGRAM EXT.ALARMSETPAY ENDINGSELECTYEARRED/BLK.MONTHEX.ALMDAYCOL.HOUR MINUTE SECOND/CARDDATE/TIMESU 12Hr. TU SAFRTHWEMO1/601/100D

4 To set P-03Make settings as shown in the figure at left, and press SET .5 To set P-04Make settings as shown in the figure at left, and press SET .

To check program settingsPress SELECT to cause PROGRAM to light up. Make the desired program No. flash. To see program settings, press

3 Check the settings on the display and press SET .Setting Number of Seconds for External Time Signal1 Press SELECT to cause EXT. ALARM to light

TABLE OF CONTENTSPRECAUTIONSFEATURESBEFORE USING THE TIME RECORDERAccessoriesLocation of ControlsInstalling Ribbon CassetteMounting Unit on WallEnviro

ResettingTo restore all the settings to factory-shipped state, push the reset switch with a pointed object.Be careful! Resetting will erase all th

28ENGLISHFollow the steps below to connect an external time signal device.6. CONNECTING EXTERNAL TIME SIGNAL 3 Insert wires into Terminals while

7. INSTALLING Ni-Cd BATTERY (optional)Follow the steps below to install a Ni-Cd battery (optional) in case of power failure.3 Hook the lid to close

Refer to the following list for proper operation.8. TROUBLESHOOTINGError No. appearsInsert the card with its right side up.Insert the card again.Open

9. SPECIFICATIONSClock accuracyCalendarPrinting systemCard mechanismDimensionsWeightPower supplyPower consumptionPower failure compensationPrint at po

31Weekly 1 Side - GreenBi-Weekly 1 Side - Green10. TIME CARD SPECIFICATIONS(1) Weekly / Bi-Weekly CardThese time cards should only be used in time ca

E6-MSignature© 2002 Lathem Time Inc. Printed in the USA.2REGULAR TIMEIN OUT IN OUTOVERTIMENamePay Period EndingFED TAXFICAMISC. / SDISTATE / PROV. TAX

Q0086 - 6120 - 3

1. PRECAUTIONSSignsVarious warnings and cautions are provided throughout this manual along with signs. Remember each sign and its explanation l

2If foreign matter should get in the unit (including a piece of metal, water, or liquid), disconnect the plug from the outlet immediate

2. FEATURESThe time table program provides the following functions: Automatic switching between black and red printingThe two-color printing system m

4Location of Controls<Display><Front view> <Back view>Daylight saving time indicationCurrent dateSU MO TU WE TH

Panel cover5Installing Ribbon Cassette1 Unlock the unit. While holding down the panel open buttons at both sides of the unit, lift th

6Mounting Unit on WallThe unit can be mounted on a wall using the supplied mounting fittings. To mount the unit on a wall, take the following steps:T