Copyright © 2009 Lathem Time Corporation. All rights reserved. Document No: USG0071 Model LX100 Proximity Door Lock User’s Guide Lathem Securit
Lathem Security Solutions Page 10 Select badge to assign as a Master, and place it over the reader window. Note: If this is a current User badge, you
LX100 User’s Guide Page 11 Adding a User Badge Place a Master badge over the reader window until you hear a beep. The blue light will begin flashing
Lathem Security Solutions Page 12 Deleting an Individual Badge Only You can not individually delete a Master badge. Only User badges can be individu
LX100 User’s Guide Page 13 Deleting All User Badges Only You can delete all of the User badges assigned to a specific Master badge without deleting t
Lathem Security Solutions Page 14 Customize Unlock Window Time This specifies the door open time after a valid badge is used. Remove the interior ha
LX100 User’s Guide Page 15 “Meeting Mode” Setting (Lock Bypass) Warning: Meeting Mode disables the lock and bypasses the use of badges for authoriza
Lathem Security Solutions Page 16 3. The light will now flash red and blue. Place the badge you want to program for Meeting Mode on the display. You
LX100 User’s Guide Page 17 Resetting the Lock Remove the Interior handle. Press and hold down the Program Button for 5 seconds. The blue LED wil
Lathem Security Solutions Page 18 Using Multiple Locks If you have purchased multiple LX100s, you can configure and change the badge accessibility to
LX100 User’s Guide Page 19 Maintaining the Lock The Lathem LX100 is designed for years of trouble-free operation. The only routine maintenance typica
Lathem Security Solutions Page 2 IMPORTANT! • Disassembling the LX100 in any way will void the warranty. • The LX100 is designed for interior use
Lathem Security Solutions Page 20 Installing the Lock PLEASE NOTE: We have used a Right hand LX100 for purposes of demonstration in this User Guide.
LX100 User’s Guide Page 21 3. Insert axle (short axle for thinner doors, longer axle for thicker doors included) into center turning hub. Make sure
Lathem Security Solutions Page 22 6. If the axle and pillars fit, you may elect to keep your current latch in place or remove it and replace with
LX100 User’s Guide Page 23 8. Push thru and allow Exterior handle to rest in latch. 9. Run wire thru rectangular opening in battery pack (to side
Lathem Security Solutions Page 24 11. Make sure Exterior handle and battery pack are straight as you tighten connector screws. 12. Connect wire to
LX100 User’s Guide Page 25 14. Install 4 new AA (1.5 volt) alkaline batteries (not included) into battery pack on Interior handle. Make sure they ar
Lathem Security Solutions Page 26 Preparing a New Door Verify that your new door is 1 3/8” – 2” thick. 1. Use the enclosed “Door Cutting Template”
LX100 User’s Guide Page 27 Latch Installation Use enclosed “Strike Plate Cutting Template” to cut and install latch in door as indicated below. 1. In
Lathem Security Solutions Page 28 Strike Plate & Dust Boot Installation 1. If you are installing on an existing door jamb, you may be able to us
LX100 User’s Guide Page 29 Troubleshooting Problem Solution No response from badge Make sure you’re holding badge on window and allow 1 – 2 seconds.
LX100 User’s Guide Page 3 Introduction The LX100 is a keyless proximity door lock that fits most standard doors. Simply replace your existing cylind
Lathem Security Solutions Page 30 One Year Warranty Lathem warrants the hardware product described in this guide against defects in material and work
LX100 User’s Guide Page 31 Accessories Accessories are normally available from the place where you originally purchased your LX100 door lock or onlin
Lathem Security Solutions Page 32
Lathem Security Solutions Page 4 Using the LX100 When a badge or key fob is placed over the reader window of the LX100, it instantly reads its unique
LX100 User’s Guide Page 5 Good Badge If the badge or key fob has been programmed into to the lock, the LX100 flashes a blue light, sounds a positive t
Lathem Security Solutions Page 6 Badges and Key Fobs The LX100 supports the use of Lathem proximity ID badges (included with lock) or optional Lathem
LX100 User’s Guide Page 7 User Badges A User badge or key fob allows access through the door. User badges or key fobs are added by a Master badge.
Lathem Security Solutions Page 8 Backup Keys The keys enclosed with your LX100 are for backup purposes in the event of badge loss or battery failure
LX100 User’s Guide Page 9 Adding a Master Badge Remove the interior handle from over the battery compartment. Press the Program Button four times, o
Kommentare zu diesen Handbüchern