Model ATX6 Wireless Wall Clock Transceiver Installation & User's Guide Copyright © 2009 Lathem Time Corporation. All rights reserved.
ATX6 Installation and User Guide Page 6 Apply a minimum of 3.5 to 4.5 lb-in torque for tightening field wires into the terminal blocks. Use Cat-3 or
ATX6 Installation and User Guide Page 7 Date/Time Set-Up: To enter the Date/Time Set-Up Mode, simultaneously press the Center (NXT) and Right (SET) b
ATX6 Installation and User Guide Page 8 4 Hours (00 ~ 12 AM/PM) Use the INC button to advance through the values. Advancing past ‘11’ will als
ATX6 Installation and User Guide Page 9 6 Time Zone (-12 ~ +12) Use the INC button to advance through the values. Advancing past ‘11’ will also t
ATX6 Installation and User Guide Page 10 9 Spring DST Week: (1,2,3,4,L) Use the INC to select which Sunday of month that Daylight Savings Time
ATX6 Installation and User Guide Page 11 14 Time Slot: (A or 0~9) To support systems that include multiple Transceivers using the same Frequency Chan
ATX6 Installation and User Guide Page 12 16 UHF Power Level (Lo / Hi) Use the INC button to toggle between Lo (4-Watt) and Hi (6-Watt) transmissi
ATX6 Installation and User Guide Page 13 P Password (000 ~ 999) For security purposes, you may set a unique password for your ATX6. To change th
ATX6 Installation and User Guide Page 14 Operating Modes: Normal: In Normal Mode, the ATX6 will listen for synchronization signals from the device se
ATX6 Installation and User Guide Page 15 If ‘PcL’, ‘485’ or ‘GPS’ is selected as the time reference, the ‘PCL’, ‘485’ or ‘GPS’ LED will flash twice
AirTime, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names mentioned in this manual may be tradem
ATX6 Installation and User Guide Page 16 Receive Mode: Automatic: If RS485, GPS or Air have been selected as the synchronization type (in Set-Up P
ATX6 Installation and User Guide Page 17 RC Transmit: If RC EMULATION is enabled [Set-Up parameter #15, above, = ‘1’] RC Transmit is selected by pre
ATX6 Installation and User Guide Page 18 Installation Examples ATX6 Stand Alone correcting Wireless Wall Clocks ATX-GPS to ATX6 correcting Wirele
ATX6 Installation and User Guide Page 19 ATX Receiving WWVB signal synchronizing an ATX 6 correcting Wireless Wall Clocks and LTR Master ATX6 throu
ATX6 Installation and User Guide Page 20 Wiring Diagrams Synchronizing the ATX6 to Lathem’s AirTime TimeSync Software via Ethernet to RS232 Converter
ATX6 Installation and User Guide Page 21 When attaching wires to the terminal block the ATX6 should be in a vertical position. If the ATX6 is horizon
ATX6 Installation and User Guide Page 22 Synchronizing a LTR0 or DWA-S to an ATX6 Synchronizing a DDC2/4-RS to an ATX6
ATX6 Installation and User Guide Page 23 Synchronizing the ATX6 to a LTR-GPS
ATX6 Installation and User Guide Page 24 Synchronizing a LTRX-512 to ATX6 using Sync Relay closure (Program ATX6 Relay closure at 12:00AM) Verify J
ATX6 Installation and User Guide Page 25 Synchronizing the ATX6 to an External Relay Closure (Program Synchronization “SYN”, verify J7 & J8 are C
Table of Contents: Introduction:... 1 Case Design ...
ATX6 Installation and User Guide Page 26 Specifications Dimensions 9" H X 5 1/8" W X 3 1/8" D Weight 3.8 lbs (1.702 kg) Di
ATX6 Installation and User Guide Page 27 Warranty Limited One-Year Limited Warranty Lathem warrants the hardware products described in this guide aga
ATX6 Installation and User Guide Page 1 Introduction: Lathem’s ATX6 is a Wireless Transceiver that can function in both “Master” (Primary), and “Repe
ATX6 Installation and User Guide Page 2 Case Design Bottom View Installation: LCD Metal Enclosure Function Buttons INC NXT SET
ATX6 Installation and User Guide Page 3 1. Choose an appropriate location to install the ATX6 on a wall. a. If you intend to use the ATX-GPS access
ATX6 Installation and User Guide Page 4 If mounting near a ceiling, make sure the top holes are at least 2” away from the ceiling. If an external amp
ATX6 Installation and User Guide Page 5 4. Attach the UHF Antenna to the ATX6’s BNC Connector and place it on top of the ATX6 or on a shelf within 12
Kommentare zu diesen Handbüchern